Select your vehicle’s year, make and model to see the Metra, PAC and iDatalink Maestro dash kits, wiring harnesses, antenna adapters and speaker sizes that fit.
The right installation parts are what make a new stereo look and work like it came from the factory. Our install parts help your new receiver, amplifier or speakers fit cleanly and connect properly to your vehicle, using trusted installation brands such as Metra and PAC.
Dash kits mount an aftermarket single or double din stereo in your dash with trim that matches your interior. Wire harnesses connect your new stereo to the factory wiring, so there’s no cutting or splicing of your vehicle’s original wires. Antenna adapters connect your factory antenna to an aftermarket radio so you keep clear AM/FM reception.
Adding an amplifier? Our amp wire kits include the power, ground and signal wiring you need to run your amplifier safely and get the most out of your system.
Not sure which parts fit your vehicle? Bring us your vehicle’s year, make and model, or come in to a store near you, and our installers will help you find the right parts for the job.
-
Rockford Fosgate RFK-HD14M5 Harley Amp Install Kit
Wire an M5-series amp into a supported Harley with the Rockford Fosgate RFK-HD14M5 Gen-3 installation kit. It is built for select 2014–2023 Road Glide, Street Glide, Ultra, and CVO models and includes 8 AWG power and ground cable, 16 AWG speaker wire, and a MAXI fuse holder sized at 60 Amp. The amplifier, source unit, and speakers are sold separately.
$369.99 -
Stinger SI123 1000 Series 2-Channel Coaxial RCA Cable
The Stinger SI123 is a 3 ft 2-channel coaxial RCA interconnect built to carry your source unit’s signal to an amplifier with minimal noise. Coaxial construction helps reject noise along the signal path. two heavy-gauge conductors per channel. It is a straightforward way to replace a worn cable or plan a clean new amplifier install. Confirm the length you need by measuring your planned route from the radio to the amplifier, allowing extra slack for bends, panels, and connections at both ends.
$8.99 -
T-SPEC VPNB4 MANL All-In-One Dist Block 4 Pos
Expand a multi-amp power system with the T-SPEC VPNB4 MANL all-in-one distribution block. The positive side accepts dual 1/0–4 AWG inputs and four 4/8 AWG fused outputs, while the negative side accepts one 1/0–4 AWG input and four 4/8 AWG outputs. Solid brass construction and a black nickel finish are specified, and MANL fuses are sold separately. Chat with CarToyz for fuse planning and professional installation.
$68.99 -
Raptor RAGU Pro Series Water-Resistant AGU Fuse Holder
The Raptor RAGU is a Pro Series AGU fuse holder for 4 or 8 AWG input and output connections on amplifier power runs. Metra lists 24K gold-plated contacts, water-resistant construction, and 3mm Allen screws for secure terminations. Pair it with an AGU fuse sized for the amplifier and wiring plan; the fuse itself is not confirmed as included on the manufacturer feature list, so verify packing before you schedule the install.
$19.99 -
Soundstream MC-1 MagiCast Wireless CarPlay Android Auto
The Soundstream MC-1 MagiCast converts a wired Apple CarPlay® or Android Auto® USB connection into a wireless experience. Plug the adapter in once, pair your phone, and the interface reconnects automatically each time you start the vehicle—no cable between phone and head unit for daily use.
$39.99$59.99 -
Rockford Fosgate RFCB200 200A Manual-Reset Circuit Breaker
The Rockford Fosgate RFCB200 is a 200-amp circuit breaker with manual reset. Its set-screw terminals accept 1/0 AWG or 4 AWG wire, providing a direct connection without ring terminals. Platinum plating and support for multiple wire sizes suit a high-current installation that calls for this breaker rating. Manual reset distinguishes this component from a replaceable fuse. The connection uses set-screw terminals.
$74.99 -
Stinger SSPRCA2F Performance Series RCA Y-Adapter
The Stinger SSPRCA2F is a RCA Y-adapter, 2 female to 1 male for splitting or combining RCA signals in a car audio system. 2 female to 1 male split for signal routing. coaxial construction. It is a handy part when you need to feed two amplifier inputs from one output, or bridge a pair of outputs into a single input. Check the plug genders on your equipment before ordering so the adapter matches your setup.
$8.99 -
T-SPEC V6-RAK1-0 V6 Amp Kit with RCA 1/0 AWG 2400W
Wire an amplifier with the T-SPEC V6-RAK1-0 V6 amp installation kit. It includes 17 ft of 1/0 AWG CCA power wire, 3 ft of 1/0 AWG CCA ground wire, 17 ft of 18 AWG remote turn-on wire, and a 17 ft V6 noise-rejecting woven coaxial RCA cable. A proprietary V8 ANL fuse holder with a 150A fuse plus nickel-plated ring and spade terminals support systems rated up to 2400W. Confirm CCA cable and fuse sizing for the amplifier before installation.
$154.99 -
Raptor RBTN Pro Series Negative Battery Terminal
The Raptor RBTN is a Pro Series negative battery terminal with a gold-plated finish for aftermarket ground distribution at the battery. It provides two outputs for 1/0 or 4 AWG cable and two outputs for 8 AWG cable so multiple ground returns can leave the post cleanly. Use it only on the negative battery connection, and confirm the vehicle post style and cable gauges before you cut or crimp anything.
$24.99 -
Stinger SI4417 4000 Series 4-Channel Twisted-Pair RCA Cable
The Stinger SI4417 is a 17 ft 4-channel directional twisted-pair RCA interconnect built to carry your source unit’s signal to an amplifier with minimal noise. Oversized OFC conductors carry a clean signal to the amplifier. 4 channels in one run for multi-channel amplifier setups. It is a straightforward way to replace a worn cable or plan a clean new amplifier install. Confirm the length you need by measuring your planned route from the radio to the amplifier, allowing extra slack for bends, panels, and connections at both ends.
$78.99 -
T-SPEC VDB3 3-Position Ground Distribution Block
Organize amplifier grounds with the T-SPEC VDB3 three-position ground distribution block. It accepts one 1/0–4 AWG input and three 4/8 AWG outputs for multi-amp ground returns. Solid brass construction with a black nickel finish and TPE soft-touch wrap supports the connection, and dual gasket sizes with T20 Torx screws are specified. Plan cable gauges before installation and ask CarToyz for a labor quote.
$29.99 -
Rockford Fosgate RFCB100 100A Manual-Reset Circuit Breaker
The Rockford Fosgate RFCB100 is a 100-amp circuit breaker with manual reset. Its set-screw terminals accept 1/0 AWG or 4 AWG wire, providing a direct connection without ring terminals. Platinum plating and support for multiple wire sizes suit a high-current installation that calls for this breaker rating. Manual reset distinguishes this component from a replaceable fuse. The connection uses set-screw terminals.
$74.99
