Select your vehicle’s year, make and model to see the Metra, PAC and iDatalink Maestro dash kits, wiring harnesses, antenna adapters and speaker sizes that fit.
The right installation parts are what make a new stereo look and work like it came from the factory. Our install parts help your new receiver, amplifier or speakers fit cleanly and connect properly to your vehicle, using trusted installation brands such as Metra and PAC.
Dash kits mount an aftermarket single or double din stereo in your dash with trim that matches your interior. Wire harnesses connect your new stereo to the factory wiring, so there’s no cutting or splicing of your vehicle’s original wires. Antenna adapters connect your factory antenna to an aftermarket radio so you keep clear AM/FM reception.
Adding an amplifier? Our amp wire kits include the power, ground and signal wiring you need to run your amplifier safely and get the most out of your system.
Not sure which parts fit your vehicle? Bring us your vehicle’s year, make and model, or come in to a store near you, and our installers will help you find the right parts for the job.
-
T-SPEC V8R174 4-Channel RCA Cable 17 Foot
Route four channels of audio signal with the T-SPEC V8R174 17 ft RCA cable. Its twisted-wire design is intended to improve noise rejection, while the ultra-flexible PVC-blended jacket helps during routing through the cabin and cargo area. Compact molded ABS ends use dual split-tip connectors for contact at the jack. Measure the path from source unit to amplifiers so the 17 ft length covers the run without excess coil.
$29.99 -
Stinger SSDB2034 Distribution Block, (2) 1/0 AWG In, (3) 4 AWG Out
The Stinger SSDB2034 is a two 1/0 AWG inputs to three 4 AWG outputs, helping you split or join power and ground runs neatly. Two 1/0 AWG inputs split to three 4 AWG outputs. brass construction for high current transfer. It is a practical part for multi-amplifier systems or for tidying an install where several cables meet. Confirm the gauges of your input and output wires before ordering so every connection seats properly.
$38.99 -
Rockford Fosgate RFDB4 Positive/Negative Battery Terminal Clamp
The Rockford Fosgate RFDB4 battery terminal clamp supports a positive or negative battery connection using its supplied sizing ring. It accommodates 4 AWG and 8 AWG cable sizes as specified for its connection ports. Custom-tooled solid brass and HPP plating provide a corrosion-resistant connection with a platinum finish. Use the available ports to organize supported cables at the battery rather than selecting a terminal by appearance alone.
$29.99 -
T-SPEC VMANL MANL Fuse Holder for 4–8 AWG Cable
Protect a 4 to 8 AWG power cable with the T-SPEC VMANL MANL fuse holder. A rotatable base allows orientation during mounting, and the holder works with MANL fuses. Dual-size gaskets for 4 and 8 AWG wire, rounded set screws, and T-20 Torx hardware support a secure clamp under the TPE overmold. The fuse is sold separately. Chat with CarToyz for amperage selection and professional installation.
$16.99 -
Stinger SPD512 1/0 AWG Power Distribution T-Block
The Stinger SPD512 is a three 1/0 AWG input/output distribution T-block, helping you split or join power and ground runs neatly. Three 1/0 AWG ports work as inputs or outputs. daisy-chain design for expanding power or ground runs. It is a practical part for multi-amplifier systems or for tidying an install where several cables meet. Confirm the gauges of your input and output wires before ordering so every connection seats properly.
$28.99 -
Rockford Fosgate RFFA200 200A ANL Fuses, Platinum Finish, 2-Pack
The Rockford Fosgate RFFA200 package contains two 200-amp ANL fuses with a platinum finish. Choose this pack when an installation specifies both the ANL fuse format and a 200-amp rating. The platinum-plated construction is part of Rockford Fosgate’s installation-accessory range. Check the existing holder and the cable and equipment requirements before choosing a replacement; the fuse format and current rating both need to match the planned circuit.
$14.99 -
Stinger SPT5210 1/0 AWG Power Wire Coupler
The Stinger SPT5210 is a joins two runs of 1/0 AWG power wire, helping you split or join power and ground runs neatly. Joins two lengths of 1/0 AWG power wire. clean, finished look at the splice point. It is a practical part for multi-amplifier systems or for tidying an install where several cables meet. Confirm the gauges of your input and output wires before ordering so every connection seats properly.
$18.99 -
T-SPEC V8-ANL150 150A ANL Fuses 2-Pack Nickel
Protect a high-current power circuit with T-SPEC V8-ANL150 nickel-plated ANL fuses. Each package contains two 150A ANL fuses, and each fuse includes a status window for a quick visual check. Install them only in a compatible ANL fuse holder that matches the cable size and amplifier load. Choose the amperage from the amplifier and wiring guidance, then ask CarToyz for holder options and installation help.
$8.99 -
Rockford Fosgate RFTB4 4 AWG Crimp Fork Terminals, 4-Pack
The Rockford Fosgate RFTB4 pack contains 4 seamed crimp-style fork terminals with a platinum finish. These terminals provide the stated connection style for a cable termination, with HPP plating for corrosion resistance. Choose the terminal style to match the connection point and confirm the cable size before crimping. The number supplied is useful when planning the required terminations, but the terminal and the equipment connection still need to be checked together.
$9.99 -
Stinger SSPRCA6 Performance Series Coaxial RCA Cable
The Stinger SSPRCA6 is a 6 ft 2-channel coaxial RCA interconnect built to carry your source unit’s signal to an amplifier with minimal noise. Coaxial construction for dependable signal transfer. paired male-to-male RCA plugs. It is a straightforward way to replace a worn cable or plan a clean new amplifier install. Confirm the length you need by measuring your planned route from the radio to the amplifier, allowing extra slack for bends, panels, and connections at both ends.
$8.99 -
Raptor RDB2 Pro Series 4-Position Ground Dist. Block
The Raptor RDB2 is a Pro Series 4-position ground distribution block for multi-component audio systems. It accepts a 1/0 or 4 AWG input and provides four 4 or 8 AWG outputs, with 24K gold-plated connections and 3mm Allen screws. Use it to organize ground returns after you confirm wire gauges and polarity, and keep each ground path as short and clean as the vehicle layout allows.
$29.99 -
Rockford Fosgate RFD4 One-In Three-Out Power Distribution Block
Organize a power connection with the Rockford Fosgate RFD4 distribution block. One input accepts 1/0 AWG or 4 AWG cable, while three outputs accept 4 AWG or 8 AWG cable. Removable internal adapter rings accommodate the supported wire sizes. The solid-brass body has a platinum finish and HPP plating for corrosion resistance, providing a defined connection point for the installation.
$34.99
